LM567, LM567C: IC Tone Decoder

LM567, LM567C: IC Tone Decoder

The LM567 and LM567C are general purpose tone decoders designed to provide a saturated transistor switch to ground when an input signal is present within the passband. The circuit consists of an I and Q detector driven by a voltage controlled oscillator which determines the center frequency of the decoder. External components are used to independently set center frequency, bandwidth and output delay.

 

Features

  • 20 to 1 Frequency Range With an External Resistor
  • Logic Compatible Output With 100-mA Current Sinking Capability
  • Bandwidth Adjustable From 0 to 14%
  • High Rejection of Out of Band Signals and Noise
  • Immunity to False Signals
  • Highly Stable Center Frequency
  • Center Frequency Adjustable from 0.01 Hz to 500 kHz

Applications

  • Touch Tone Decoding
  • Precision Oscillator
  • Frequency Monitoring and Control
  • Wide Band FSK Demodulation
  • Ultrasonic Controls
  • Carrier Current Remote Controls
  • Communications Paging Decoders

 

Output Filter

To eliminate undesired signals that could trigger the output stage, a post detection filter is featured in the LM567C. This filter consists of an internal resistor (4.7K-Ω) and an external capacitor. Although typically external capacitor value is not critical, it is recommended to be at least twice the value of the loop filter capacitor. If the output filter capacitor value is too large, the turn-on and turn off-time of the output will present a delay until the voltage across this capacitor reaches the threshold level.

Loop Filter

The phase locked loop (PLL) included in the LM567 has a pin for connecting the low pass loop filter capacitor. The selection of the capacitor for the filter depends on the desired bandwidth. The device bandwidth selection is different according to the input voltage level. Refer to the Operation With Vi < 200m – VRMS section and the Operation With Vi > 200m – VRMS section for more information about the loop filter capacitor selection.

Logic Output

The LM567 is designed to provide a transistor switch to ground output when the input signal frequency matches the center frequency pass band. The logic output is an open collector power transistor that requires an external load resistor that is used to regulate the output current level.

 

Bild Teil # Hersteller Beschreibung Stock Preis Kaufen
12103C103K4T2A
Kyocera AVX
Multilayer Ceramic Capacitors MLCC - SMD/SMT 25V .01uF X7R 1210 Tol 10% AEC-Q200
0
1+
$0.0528
10+
$0.0366
100+
$0.0219
500+
$0.0165
1000+
$0.0139
Detail
C0805C821K2RALTU
KEMET Electronics
Multilayer Ceramic Capacitors MLCC - SMD/SMT 200V 820pF X7R 0805 10%
0
1+
$0.0516
10+
$0.0362
100+
$0.0218
500+
$0.0163
1000+
$0.0138
Detail
12101C103K4T2A
Kyocera AVX
Multilayer Ceramic Capacitors MLCC - SMD/SMT 100V .01uF X7R 1210 Tol 10% AEC-Q200
0
1+
$0.0528
10+
$0.0366
100+
$0.0219
500+
$0.0165
1000+
$0.0139
Detail
C1812X275M1RALTU
KEMET Electronics
Multilayer Ceramic Capacitors MLCC - SMD/SMT 100volts 2.7uF 20% X7R
0
1+
$0.2328
10+
$0.1788
100+
$0.1137
500+
$0.0999
1000+
$0.0697
Detail
Seite 1 / 1